Yaskawa SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET

Sigma -V series servo motor SGMPS.
Rated output: 200W (0.2KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Corresponding to the RoHS instruction: in accordance with the RoHS directive SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET SGD7S-200A20A001
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlCapacity type of direct drive servo motor SGMCS.
Rated torque: M \/ 45N.
Servo motor outside diameter size: 230mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 miinutes SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) SGD7S-200A20A001 MECHATROLINK-III Communications Manual SGD7S-200A20A001 INSTRUCTION SHEET.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation