Yaskawa SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL

Sigma -V series servo motor SGMSV.
Rated output: 1.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL.
Equipped with a high resolution serial encoder (20 bit) SGM7P-01AFAHC01
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL.
Rated speed: 1500r\/min.
Power: 11Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlEquipped with DeviceNet communication function type servo unit (servo controlled power supply drive type)
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (servo control power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit are connected through the communication netwwork, the connection is greatly saved SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function SGM7P-01AFAHC01 Manual SGM7P-01AFAHC01 HARDWARE MANUAL.