Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMGH type servo motor
>> SGMGH-09A2D6D | Yaskawa Motor for high precision machine tool SGMGH-09A2D6D
SGMGH-09A2D6D | Yaskawa Motor for high precision machine tool SGMGH-09A2D6D
Yaskawa SGMGH-09A2D6D Product information and technical parameters：
Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-09A2D6D
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa SGMGH-09A2D6D SGMGH-09A2D6D
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -v series servo unit SGDV Yaskawa SGMGH-09A2D6D.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMGH-09A2D6D. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-09A2D6D.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-09A2D6D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties Yaskawa SGMGH-09A2D6D SGMGH-09A2D6D
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -v series servo unit SGDV Yaskawa SGMGH-09A2D6D.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMGH-09A2D6D. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-09A2D6D.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-09A2D6D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Motor for high precision machine tool SGMGH-03A2D6D
next one: Yaskawa Motor for high precision machine tool SGMGH-12A2D6D
Related download