Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGDV-____25 Type (Used by linear servo motor)
>> SGDV-5R4D25B | Yaskawa Servo driver for linear servo motor SGDV-5R4D25B
SGDV-5R4D25B | Yaskawa Servo driver for linear servo motor SGDV-5R4D25B
Yaskawa SGDV-5R4D25B Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-5R4D25B
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Sigma -V series servo motor SGMSV.
Rated output: 1.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1 Yaskawa SGDV-5R4D25B. 0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGDV-5R4D25B
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type Yaskawa SGDV-5R4D25B.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type Yaskawa SGDV-5R4D25B.
Rated speed: 1500r\/min.
Power: 11Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor type SGMPH (speed: 3000r/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phasee 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer SGDV-5R4D25B.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a verry seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGDV-5R4D25B.
Rated output: 1.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1 Yaskawa SGDV-5R4D25B. 0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGDV-5R4D25B
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type Yaskawa SGDV-5R4D25B.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type Yaskawa SGDV-5R4D25B.
Rated speed: 1500r\/min.
Power: 11Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor type SGMPH (speed: 3000r/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phasee 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer SGDV-5R4D25B.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a verry seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGDV-5R4D25B.
...More relevant models >>>>
Last one: Yaskawa Servo driver for linear servo motor SGDV-5R4D25A020000
next one: Yaskawa Servo driver for linear servo motor SGDV-5R4D25B002000
Related download