Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 2kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Sigma -V series servo motor SGMSV.
Rated output: 1.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) Yaskawa SGDV-8R4D15A002000.
Equipped with a high resolution serial encoder (20 bit) SGDV-8R4D15A002000
Standard using IP67 (7.0kw for IP22).
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type Yaskawa SGDV-8R4D15A002000.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type Yaskawa SGDV-8R4D15A002000.
Rated speed: 1000r\/min.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGDV-8R4D15A002000.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen