Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMCS type direct drive motor
>> SGMCS-45MDA11 | Yaskawa Direct drive servo motor SGMCS-45MDA11
SGMCS-45MDA11 | Yaskawa Direct drive servo motor SGMCS-45MDA11
Yaskawa SGMCS-45MDA11 Manual And Instructions
SGMCS-45MDA11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-45MDA11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-45MDA11
Capacity type of direct drive servo motor SGMCS.
Rated torque: M \/ 45N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMCS-45MDA11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-45MDA11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-45MDA11
Capacity type of direct drive servo motor SGMCS.
Rated torque: M \/ 45N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) Yaskawa SGMCS-45MDA11.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGMCS-45MDA110kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type Yaskawa SGMCS-45MDA11.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor Yaskawa SGMCS-45MDA11.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-45MDA11.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMCS-45MDA11.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) Yaskawa SGMCS-45MDA11.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGMCS-45MDA110kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type Yaskawa SGMCS-45MDA11.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor Yaskawa SGMCS-45MDA11.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-45MDA11.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMCS-45MDA11.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa Direct drive servo motor SGMCS-35MDA11
next one: Yaskawa Direct drive servo motor SGMCS-80MDA11
Related download