YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMGV type motor >> SGMGV-1EA3C6B | Yaskawa Rotary servo motor SGMGV-1EA3C6B

SGMGV-1EA3C6B | Yaskawa Rotary servo motor SGMGV-1EA3C6B

Yaskawa SGMGV-1EA3C6B Manual And Instructions
SGMGV-1EA3C6B Setup Rotational MotorProduct Manual

Yaskawa SGMGV-1EA3C6B Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-1EA3C6B
Sigma -V series servo motor SGMGV.
Rated output: 15kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Large capacity servo unit.
Maximum applicable motor capacity: 22KW.
Power supply voltage: three phase AC200V.
Fastening: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: B.
Optional parts (hardware): ventilation duct installation type.
Improve the performance of large torque transmission machinery!
Vibration suppression function Yaskawa SGMGV-1EA3C6B.
When the driving system of the machine is vibrating, the observer is used to reduce the vibration and suppress the vibration of the device SGMGV-1EA3C6B
Friction compensation function.
Even when the load fluctuation, the gain can be suppressed without changing the position deviation.
Therefore, the overshoot can be suppressed to ensure the stability of the device Yaskawa SGMGV-1EA3C6B.
Feature tracking control.
Even the lower mechanical properties, but also the characteristics of the mechanical recovery,
Make the mechanical properties of the control action, thereby reducing the time to adjust the timeDesign sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: with DC24V brake.
Partial flat series: the need to install the servo motor in a small space Yaskawa SGMGV-1EA3C6B.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.6Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-1EA3C6B.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMGV-1EA3C6B.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>