YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMGV type motor >> SGMGV-20D3C2B | Yaskawa Rotary servo motor SGMGV-20D3C2B

SGMGV-20D3C2B | Yaskawa Rotary servo motor SGMGV-20D3C2B

Yaskawa SGMGV-20D3C2B Manual And Instructions
SGMGV-20D3C2B Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMGV-20D3C2B Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20D3C2B
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Full closed loop module.
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) Yaskawa SGMGV-20D3C2B.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGV-20D3C2B
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating) Yaskawa SGMGV-20D3C2B. High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 3.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-II communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: pressure feedback control function Yaskawa SGMGV-20D3C2B.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-20D3C2B.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMGV-20D3C2B.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>