YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGMPS type motor >> SGMPS-15ACE61E | Yaskawa Medium inertia flat type motor SGMPS-15ACE61E

SGMPS-15ACE61E | Yaskawa Medium inertia flat type motor SGMPS-15ACE61E

Yaskawa SGMPS-15ACE61E Manual And Instructions
SGMPS-15ACE61E Setup Rotational MotorProduct Manual

Yaskawa SGMPS-15ACE61E Product information and technical parameters:
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-15ACE61E
Sigma -V series servo motor SGMPS.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 5.0kw.
Power supply voltage: three phase AC400V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard Yaskawa SGMPS-15ACE61E.
Optional modules: INDEXER module.
Simple.
By programming and serial programming, easy implementation of motion control SGMPS-15ACE61E
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table Yaskawa SGMPS-15ACE61E.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller Yaskawa SGMPS-15ACE61E. Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 11Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control ccircuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMPS-15ACE61E.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMPS-15ACE61E.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>