Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMSV type motor
>> SGMSV-20DDA2C | Yaskawa servo motor SGMSV-20DDA2C
SGMSV-20DDA2C | Yaskawa servo motor SGMSV-20DDA2C
Yaskawa SGMSV-20DDA2C Manual And Instructions
SGMSV-20DDA2C Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-20DDA2C Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-20DDA2C
Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-20DDA2C Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-20DDA2C Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-20DDA2C
Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMSV-20DDA2C SGMSV-20DDA2C Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time Yaskawa SGMSV-20DDA2C.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly Yaskawa SGMSV-20DDA2C. Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Key: straight shaft end uranium belt with screw.
Optional parts: with oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 7.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware options: paint.
It is helpful to the servo performance of ultra high speed and ultra precision control SGMSV-20DDA2C.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suuppression function SGMSV-20DDA2C.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth drive
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMSV-20DDA2C SGMSV-20DDA2C Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time Yaskawa SGMSV-20DDA2C.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly Yaskawa SGMSV-20DDA2C. Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Key: straight shaft end uranium belt with screw.
Optional parts: with oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 7.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware options: paint.
It is helpful to the servo performance of ultra high speed and ultra precision control SGMSV-20DDA2C.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suuppression function SGMSV-20DDA2C.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth drive
...More relevant models >>>>
Last one: 
next one: Related download